View Issue Details
| ID | Project | Category | View Status | Date Submitted | Last Update |
|---|---|---|---|---|---|
| 0000026 | Freifunk Franken Firmware | General | public | 2017-01-15 17:38 | 2019-10-02 12:49 |
| Reporter | ChristianD | Assigned To | reddog | ||
| Priority | normal | Severity | minor | Reproducibility | sometimes |
| Status | resolved | Resolution | fixed | ||
| Product Version | 20170110 | ||||
| Target Version | 20170918 | ||||
| Summary | 0000026: Picostation bootet nach flashen nicht richtig | ||||
| Description | Nach dem Upgrade einer Picostation kommen nicht alle Interfaces richtig hoch. UART Log im Anhang. | ||||
| Tags | No tags attached. | ||||
| Attached Files | pico.txt (11,218 bytes)
[ 38.840000] tun: Universal TUN/TAP device driver, 1.6
[ 38.840000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 38.850000] l2tp_core: L2TP core driver, V2.0
[ 38.860000] l2tp_netlink: L2TP netlink interface
[ 38.870000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 38.880000] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 38.880000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 38.900000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 38.950000] batman_adv: B.A.T.M.A.N. advanced 2013.4.0 (compatibility version d
[ 38.980000] u32 classifier
[ 38.980000] input device check on
[ 38.980000] Actions configured
[ 38.990000] Mirror/redirect action on
[ 39.000000] nf_conntrack version 0.5.0 (447 buckets, 1788 max)
[ 39.100000] arp_tables: (C) 2002 David S. Miller
[ 39.110000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf8
[ 39.120000] Backport generated by backports.git backports-20151218-0-g2f58d9d
[ 39.170000] Ebtables v2.0 registered
[ 39.180000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 39.640000] xt_time: kernel timezone is -0000
[ 39.910000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 39.920000] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[ 39.950000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
[ 50.410000] IPv6: ADDRCONF(NETDEV_UP): br-mesh: link is not ready
[ 54.440000] IPv6: ADDRCONF(NETDEV_UP): w2ap: link is not ready
[ 54.460000] device w2ap entered promiscuous mode
[ 54.490000] br-mesh: port 1(w2ap) entered forwarding state
[ 54.490000] br-mesh: port 1(w2ap) entered forwarding state
[ 54.500000] IPv6: ADDRCONF(NETDEV_CHANGE): w2ap: link becomes ready
[ 54.520000] IPv6: ADDRCONF(NETDEV_CHANGE): br-mesh: link becomes ready
[ 55.120000] IPv6: ADDRCONF(NETDEV_UP): w2mesh: link is not ready
[ 55.180000] w2mesh: Created IBSS using preconfigured BSSID 02:ca:ff:ee:ba:be
[ 55.190000] w2mesh: Creating new IBSS network, BSSID 02:ca:ff:ee:ba:be
[ 55.190000] IPv6: ADDRCONF(NETDEV_CHANGE): w2mesh: link becomes ready
[ 55.580000] batman_adv: bat0: Adding interface: w2mesh
[ 55.590000] batman_adv: bat0: Interface activated: w2mesh
[ 56.000000] batman_adv: bat0: Changing gw mode from: off to: client
[ 56.030000] batman_adv: bat0: gw_sel_class: Changing from: 20 to: 1
[ 56.030000] batman_adv: bat0: network_coding: Changing from: enabled to: disabd
[ 56.490000] br-mesh: port 1(w2ap) entered forwarding state
[ 59.360000] random: nonblocking pool is initialized
[ 63.950000] br-mesh: port 1(w2ap) entered disabled state
[ 63.950000] device w2ap left promiscuous mode
[ 63.960000] br-mesh: port 1(w2ap) entered disabled state
[ 64.190000] batman_adv: bat0: Interface deactivated: w2mesh
[ 64.190000] batman_adv: bat0: Removing interface: w2mesh
[ 65.180000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 69.090000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 70.970000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 70.990000] IPv6: ADDRCONF(NETDEV_UP): br-mesh: link is not ready
[ 72.580000] IPv6: ADDRCONF(NETDEV_UP): w2ap: link is not ready
[ 72.610000] device w2ap entered promiscuous mode
[ 72.620000] br-mesh: port 1(w2ap) entered forwarding state
[ 72.620000] br-mesh: port 1(w2ap) entered forwarding state
[ 72.690000] IPv6: ADDRCONF(NETDEV_CHANGE): w2ap: link becomes ready
[ 72.690000] IPv6: ADDRCONF(NETDEV_CHANGE): br-mesh: link becomes ready
[ 73.100000] IPv6: ADDRCONF(NETDEV_UP): w2mesh: link is not ready
[ 73.130000] w2mesh: Created IBSS using preconfigured BSSID 02:ca:ff:ee:ba:be
[ 73.140000] w2mesh: Creating new IBSS network, BSSID 02:ca:ff:ee:ba:be
[ 73.150000] IPv6: ADDRCONF(NETDEV_CHANGE): w2mesh: link becomes ready
[ 73.810000] br-mesh: port 1(w2ap) entered disabled state
[ 73.830000] device w2ap left promiscuous mode
[ 73.830000] br-mesh: port 1(w2ap) entered disabled state
[ 73.920000] IPv6: ADDRCONF(NETDEV_UP): br-mesh: link is not ready
[ 74.830000] IPv6: ADDRCONF(NETDEV_UP): w2ap: link is not ready
[ 76.370000] IPv6: ADDRCONF(NETDEV_UP): w2ap: link is not ready
[ 77.800000] IPv6: ADDRCONF(NETDEV_UP): w2ap: link is not ready
[ 78.370000] IPv6: ADDRCONF(NETDEV_UP): br-mesh: link is not ready
[ 82.090000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 82.120000] IPv6: ADDRCONF(NETDEV_UP): br-mesh: link is not ready
[ 83.620000] IPv6: ADDRCONF(NETDEV_UP): w2ap: link is not ready
[ 83.630000] device w2ap entered promiscuous mode
[ 83.660000] br-mesh: port 1(w2ap) entered forwarding state
[ 83.660000] br-mesh: port 1(w2ap) entered forwarding state
[ 83.670000] IPv6: ADDRCONF(NETDEV_CHANGE): w2ap: link becomes ready
[ 83.690000] IPv6: ADDRCONF(NETDEV_CHANGE): br-mesh: link becomes ready
[ 84.140000] IPv6: ADDRCONF(NETDEV_UP): w2mesh: link is not ready
[ 84.200000] w2mesh: Created IBSS using preconfigured BSSID 02:ca:ff:ee:ba:be
[ 84.210000] w2mesh: Creating new IBSS network, BSSID 02:ca:ff:ee:ba:be
[ 84.210000] IPv6: ADDRCONF(NETDEV_CHANGE): w2mesh: link becomes ready
[ 84.880000] br-mesh: port 1(w2ap) entered disabled state
[ 84.920000] device w2ap left promiscuous mode
[ 84.930000] br-mesh: port 1(w2ap) entered disabled state
[ 85.000000] IPv6: ADDRCONF(NETDEV_UP): br-mesh: link is not ready
[ 85.930000] IPv6: ADDRCONF(NETDEV_UP): w2ap: link is not ready
[ 87.470000] IPv6: ADDRCONF(NETDEV_UP): w2ap: link is not ready
[ 89.500000] IPv6: ADDRCONF(NETDEV_UP): w2ap: link is not ready
[ 90.260000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 93.970000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 93.980000] IPv6: ADDRCONF(NETDEV_UP): br-mesh: link is not ready
[ 95.530000] IPv6: ADDRCONF(NETDEV_UP): w2ap: link is not ready
[ 95.570000] device w2ap entered promiscuous mode
[ 95.590000] br-mesh: port 1(w2ap) entered forwarding state
[ 95.600000] br-mesh: port 1(w2ap) entered forwarding state
[ 95.600000] IPv6: ADDRCONF(NETDEV_CHANGE): w2ap: link becomes ready
[ 95.630000] IPv6: ADDRCONF(NETDEV_CHANGE): br-mesh: link becomes ready
[ 96.010000] IPv6: ADDRCONF(NETDEV_UP): w2mesh: link is not ready
[ 96.060000] w2mesh: Created IBSS using preconfigured BSSID 02:ca:ff:ee:ba:be
[ 96.070000] w2mesh: Creating new IBSS network, BSSID 02:ca:ff:ee:ba:be
[ 96.070000] IPv6: ADDRCONF(NETDEV_CHANGE): w2mesh: link becomes ready
[ 96.750000] br-mesh: port 1(w2ap) entered disabled state
[ 96.800000] device w2ap left promiscuous mode
[ 96.800000] br-mesh: port 1(w2ap) entered disabled state
[ 96.820000] IPv6: ADDRCONF(NETDEV_UP): br-mesh: link is not ready
[ 98.290000] IPv6: ADDRCONF(NETDEV_UP): w2ap: link is not ready
[ 100.620000] IPv6: ADDRCONF(NETDEV_UP): w2ap: link is not ready
[ 102.080000] IPv6: ADDRCONF(NETDEV_UP): w2ap: link is not ready
root@SchlagDenAlfred:/# ifconfig
br-mesh Link encap:Ethernet HWaddr 00:27:22:80:F2:CA
inet6 addr: fdff::27:2280:f2ca/64 Scope:Global
inet6 addr: fdff::227:22ff:fe80:f2ca/64 Scope:Global
inet6 addr: fdff::1/64 Scope:Global
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth0 Link encap:Ethernet HWaddr 02:27:22:80:F2:CA
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:4
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:18 errors:0 dropped:0 overruns:0 frame:0
TX packets:18 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1476 (1.4 KiB) TX bytes:1476 (1.4 KiB)
root@SchlagDenAlfred:/#
| ||||
|
|
Bitte nochmal mit LEDE testen. |
|
|
Fehler scheint auch bei LEDE aufzutreten. Auffällig ist, das es bei Geräten mit nur einen LAN Anschluss passiert. Eben passiert mit einer Bullet-M und einem WA850RE. Diverse andere Router (841 v7 v8 und 842) liefen nach dem Flashen wieder problemlos hoch. Leider waren das remote Updates so das ich kein serielles Log habe. |
|
|
Ich habe gerade die Firmware auf zwei Ubiquiti Nanostation M per Remote (Web UI/IPv6 über Router in der gleichen Hood) geupdatet (20160310 auf 20170110). Verwendetes Image: fff-20170110-ar71xx-g-ubnt-nano-m-squashfs-sysupgrade.bin Dabei hatte ich in beiden Fällen das Problem, dass das Update keinen Neustart der Nanostation ausgelöst hat, sondern diese einfach nicht mehr aus dem Netz erreichbar war (> 1h Wartezeit, auch offline im Monitoring). Ich musste dann vor Ort anrufen und den Gaststättenbetreiber bitten, jeweils den Stecker rauszuziehen und wieder reinzustecken. Danach war die Firmware aktuell und alles, wie es sein sollte. (Alle WR841N 10/11 haben das gleiche Prozedere ohne Probleme durchlaufen, es liegt also wohl an der Nanostation). |
|
|
Hab inzwischen vier Nanostations geupdatet und musste in allen Fallen manuell neu starten (2x WebUI, 2x SSH). Nie beobachtet bei WR841n (>10 Updates...) Firmware immer 20170110. |
|
|
Da ich leider nicht editieren kann: Meine zuvor geschilderten Fälle waren alle PICOstations M2, keine Nanostations. Habe nun die entsprechenden Geräte von 20170110 auf eine Custom-Variante der 20170218-alpha mit Patches aktualisiert und hatte diesmal bei fünf Geräten keinen einzigen Ausfall. (Alles Remote per WebUI). Ob das jetzt an der neueren Firmware liegt oder Zufall war: Keine Ahnung. |
|
|
Bitte mit 20170918-beta testen. |
|
|
Habe bei einer Nanostation Loco M2 und der 20170918-beta auch keine Probleme mehr feststellen können. Fährt sauber nach dem flashen hoch. |
|
|
Hab eine Pico M2HP mit der 20170918-beta per webui-remote und sysupgrade aktualisiert. Fährt ohne Probleme hoch. Gerät hat nur WLAN mesh - kein WAN uplink. |
| Date Modified | Username | Field | Change |
|---|---|---|---|
| 2017-01-15 17:38 | ChristianD | New Issue | |
| 2017-01-15 17:38 | ChristianD | File Added: pico.txt | |
| 2017-01-15 17:55 | ChristianD | Severity | block => minor |
| 2017-01-15 19:57 | ChristianD | Reproducibility | always => sometimes |
| 2017-02-18 18:49 | reddog | Target Version | 20180726-beta => 20170918 |
| 2017-02-18 18:49 | reddog | Note Added: 0000048 | |
| 2017-03-13 11:21 | ChristianD | Note Added: 0000056 | |
| 2017-03-13 11:22 | ChristianD | Note Edited: 0000056 | |
| 2017-04-02 19:47 | Adrian Schmutzler | Note Added: 0000063 | |
| 2017-05-10 15:37 | Adrian Schmutzler | Note Added: 0000077 | |
| 2017-08-25 11:56 | Adrian Schmutzler | Note Added: 0000133 | |
| 2017-09-19 21:34 | reddog | Note Added: 0000138 | |
| 2017-09-20 21:12 | moexe | Note Added: 0000142 | |
| 2017-09-22 12:02 | Aries | Note Added: 0000143 | |
| 2017-09-23 13:20 | reddog | Assigned To | => reddog |
| 2017-09-23 13:20 | reddog | Status | new => resolved |
| 2017-09-23 13:20 | reddog | Resolution | open => fixed |
| 2019-10-02 12:48 | fbl | Category | Freifunk Franken Firmware => General |
| 2019-10-02 12:48 | fbl | Category | General => General2 |
| 2019-10-02 12:49 | fbl | Category | General2 => General |
